We believe this is simply the best active AB/Y pedal available. It features dual buffered and transformer isolated outputs, which means no signal loss, no ground loops, and no tone suck. And the circuit runs on an internally boosted dual rail power supply for increased headroom and clarity. We've also included a phase switch to keep amps or separate channels in phase.

Another user friendly feature - when the Y switch is engaged, the selected A or B LED will remain illuminated, so you'll know which output will be active when the Y switch is disengaged.

Our AB/Y is hand-wired in the USA with silver plated 20AWG wire and no PCB mounted jacks, switches or plugs. This pedal is built to last and comes housed in a powder coated, laser etched aluminum enclosure. As always with every piece of de Lisle gear, it's back by a lifetime warranty for your peace of mind.

The de Lisle Dual Line Driver + is a great solution for multiple amp setups with longer cable runs. It features two buffered and transformer isolated outputs to eliminate ground loops and signal loss. These outputs also have individual phase switches. The direct out can be used to feed a third amp or tuner. The circuit runs on an internally boosted dual rail power supply for increased headroom and clarity (15vpp). 

The de Lisle Dual Line Driver + is hand-wired in the USA with no PCB mounted jacks, switches or plugs. This pedal is built to last and comes housed in a powder coated, laser etched aluminum enclosure. As always with every piece of de Lisle gear, it's back by a lifetime warranty for your peace of mind.

Designed with feedback from Justin Adams, guitarist for Robert Plant, the de Lisle Notch Box is based on the Gibson ® Varitone circuit found in guitars like the ES-355, Lucille and Blueshawk. Our pedal version offers 6 preset notch filters for various tones along with a potentiometer to control the notch depth. There is a voicing switch that allows you to toggle between the original '59 circuit and the redesigned Varitone introduced in the Blueshawk - that's 12 linearly variable filters in all!

The original Varitone was a simple passive device, so there was a fair amount of signal loss at higher settings. To counteract this, the Notch Box has an adjustable MOSFET boost. Set it to unity gain so your the effected and dry signals are at the same level.

The Notch Box was designed with other pedals in mind, so it has a high impedance input and a low impedance output. It will fit nicely at any position on your board.

The de Lisle Notch Box is hand-wired in the USA with silver plated 20AWG wire and no PCB mounted jacks, switches or plugs. This pedal is built to last and comes housed in a powder coated aluminum enclosure. As always with every piece of de Lisle gear, it's back by a lifetime warranty for your peace of mind.

The de Lisle ABC pedal is a great solution for multiple amp setups. It enables you to safely connect a guitar to one, two or three amps at a time without introducing ground loop hum. So don't defeat the safety grounds on your amps!

It features a direct out plus dual buffered and transformer isolated outputs, which means no signal loss, no ground loops, and no tone suck. And the circuit runs on an internally boosted dual rail power supply for increased headroom and clarity. We've also included a phase switch to keep amps or separate channels in phase.

Another user friendly feature - each output has a unqiuely colored LED, so you'll know exactly which switch you're stepping even on the darkest stage. Each output is individually selectable, so you can use any combination of amps you want.

The de Lisle ABC is hand-wired in the USA with silver plated 20AWG wire and no PCB mounted jacks, switches or plugs. This pedal is built to last and comes housed in a powder coated, laser etched aluminum enclosure. As always with every piece of de Lisle gear, it's back by a lifetime warranty for your peace of mind.

The de Lisle Amp-Speaker Selector (Version 1) was designed as a studio tool to conveniently route the output from any of the connected amplifiers to an isolation cabinet. Alternatively, a single amplifier can be paired with one of up to three individual cabinets. Signal and ground connections from the amps are isolated, and as a precaution, the unused amps see a load. Similarly, when used as a cabinet selector, jacks with no cable inserted will be switched to an internal load. So, one can use a single cabinet or two cabinets without worrying about switching to an open cabinet jack.

The de Lisle Speaker Cabinet AB Selector Switch allows you to toggle between two speaker cabinets connected to the same amp. If your amplifier has multiple output jacks for different impedance cabinets, you can connect a second output to the ALT Z jack and toggle between two cabinets connected to different impedance outputs on the same amp. There's also a remote input that will allow you to operate the switch from a distance with a simple TS latching switch.

The de Lisle Amp-Speaker Selector V2 was designed as a studio tool to conveniently route the output of up to four amplifiers to various speaker cabinets. Just connect your amps' outputs to numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: the four switches on the front panel correspond to the four speaker connections. The 0-4 positions of each bank match that speaker cabinet to an amplifier (or 0 for not connected). Use multiple amps at the same time, swap speaker cabinets between amps, or connect multiple speakers to an amp in parallel. Signal and ground connections from the amps are always isolated from one another. And as a precaution, the unused amps see a load.

Save 15% with the Amp-Speaker Selector V3 and Drop Box 50W Linearly Variable Attenuator bundle! Add our transformer isolated ABC switch to route the input signal for more savings!

The de Lisle Amp-Speaker Selector V3 was designed as a studio tool to conveniently route the output of up to three amplifiers to various speaker cabinets. This version features a loop to allow a single attenuator or similar device to be easily shared between any combination of the amps and speakers.

Just connect your amps' outputs to numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: the three Speaker switches on the front panel correspond to the three speaker connections. The 0-3 positions of each bank match that speaker cabinet to an amplifier (or 0 for not connected).

Connect your attenuator's input to the Send jack and its output to the Return jack. Use the front panel Send knob to connect the attenuator to any of the amps' outputs. Then, set one or more of the Speaker knobs to the return arrow icon (position 5).

Use multiple amps at the same time, swap speaker cabinets between amps, share a single attenuator or connect multiple speakers to an amp in parallel. Signal and ground connections from the amps are always isolated from one another. And as a precaution, the unused amps see a load.

The de Lisle 15W Reactive Attenuator allows you to knock your amp's volume down to a more manageable level while maintaining its natural feel thanks to the reactive load. Attenuation is linearly variable up to -20dB. Our unique design eliminates the need for impedance matching at the amp. Just connect the attenuator to your amp's 8 ohm output, then you can use any combination of cabs as long as the total load is between 16 and 4 ohms. Use the transformer isolated D.I. to go straight into your DAW and load up your favorite IRs with the ability to record silently.