de Lisle Amp-Speaker Selector 4×4 Pro

de Lisle Guitar Co. de Lisle Amp-Speaker Selector 4x4 Pro The de Lisle Amp-Speaker 4x4 Pro was designed to improve workflow in the studio by eliminating the need to re-cable amps, fx and cabs. This version expands on our previous designs by incorporating simultaneous input switching, fx loop switching and an attenuator loop. Turning the front panel Amplifier dial will do the following: • Route the guitar input to the selected amp's input • Send the amp's output to the selected speaker • Mute all unused amps at their input • Switch unused amps to a load • Route the Pedalboard In / Out to the active amp's FX send and return jacks • Place unused amp FX loops in bypass When activated, the attenuator follows the selected amp and cabinet, so you can easily connect your Ox, Fryette, etc. to any combination of amplifier and cabinet. Should you prefer to go straight from amp to cabinet, just place the Attenuator switch in the down position to bypass the attenuator loop. Similarly, the active amp's FX loop can be bypassed by placing the FX Loop switch in the down position. The 4x4 Pro runs off a standard 2.1mm/5.5mm center negative 9V supply, which is boosted internally for increased signal headroom. Amplifiers are transformer isolated to prevent ground loops. 0 stars, based on 0 reviews 0 5
$999.00

de Lisle Amp-Speaker Selector 4x4 Pro

$999.00
de Lisle Amp-Speaker Selector 4x4 Pro
de Lisle Amp-Speaker Selector 4x4 Pro
de Lisle Amp-Speaker Selector 4x4 Pro
de Lisle Amp-Speaker Selector 4x4 Pro
de Lisle Amp-Speaker Selector 4x4 Pro
de Lisle Amp-Speaker Selector 4x4 Pro
de Lisle Amp-Speaker Selector 4x4 Pro
de Lisle Amp-Speaker Selector 4x4 Pro
de Lisle Amp-Speaker Selector 4x4 Pro
de Lisle Amp-Speaker Selector 4x4 Pro

de Lisle Amp-Speaker Selector 4x4 Pro

$999.00
The de Lisle Amp-Speaker 4x4 Pro was designed to improve workflow in the studio by eliminating the need to re-cable amps, fx and cabs. This version expands on our previous designs by incorporating simultaneous input switching, fx loop switching and an attenuator loop.

Turning the front panel Amplifier dial will do the following:

• Route the guitar input to the selected amp's input
• Send the amp's output to the selected speaker
• Mute all unused amps at their input
• Switch unused amps to a load
• Route the Pedalboard In / Out to the active amp's FX send and return jacks
• Place unused amp FX loops in bypass

When activated, the attenuator follows the selected amp and cabinet, so you can easily connect your Ox, Fryette, etc. to any combination of amplifier and cabinet. Should you prefer to go straight from amp to cabinet, just place the Attenuator switch in the down position to bypass the attenuator loop. Similarly, the active amp's FX loop can be bypassed by placing the FX Loop switch in the down position.

The 4x4 Pro runs off a standard 2.1mm/5.5mm center negative 9V supply, which is boosted internally for increased signal headroom. Amplifiers are transformer isolated to prevent ground loops.
Please select a chassis style
Maximum quantity exceeded
Minimum purchase amount of 0 is required
Maximum purchase amount of 0 is allowed
Your Price: $999.00
999.000
A one-time price of $999.00 will be added to your order.
Facebook
Twitter
Email
Pinterest
Google+
Digg
  • Specs
• Input Impedance: 1 Meg
• Output Impedance: 500 Ohm
• Input Sensitivity: +15 Vp-p
• Switching Time: 4-8ms
• Contact Resistance: 0.075 Ohm
• Power Consumption: 2.6W Max
• Guitar / Pedalboard Input (1)
• Amplifier Input (4)
• Amplifier Output (4)
• Speaker Input (4)
• Attenuator Input (1)
• Attenuator Output(1)
• Attenuator Bypass Switch
• FX Send (4)
• FX Return (4)
• Pedalboard In
• Pedalboard Out
• Transformer Isolation
• Internally Isolated DC Power Supply
• Increased Signal Headroom
• Silver Relay Contacts with Gold Overlay
• Protection Loads for Unused Amplifiers
• Auto Muting of Unused Amplifiers
• Auto Bypass of Unused Amplifier FX Loops
• Premium 2U Rack Chassis with Laser Etched Panels
• 9VDC 500mA Power Supply Included (300mA Minimum Required)
• Hand-Wired
• 150W Maximum Power
• Lifetime Warranty
• Manual

Related Products

  • de Lisle Drop Box Linearly Variable 50W Attenuator

    de Lisle Drop Box Linearly Variable 50W Attenuator

    $229.00

    The de Lisle Drop Box 50W attenuator allows you to knock your amp's volume down to a more manageable level. It's linearly adjustable from -2dB to -18dB. Just insert the Drop Box between your amp's output and the speaker and you're ready to rock!

    Maximum quantity exceeded
    Minimum purchase amount of 0 is required
    de Lisle Drop Box Linearly Variable 50W Attenuator

    de Lisle Drop Box Linearly Variable 50W Attenuator

    The de Lisle Drop Box 50W attenuator allows you to knock your amp's volume down to a more manageable level. It's linearly adjustable from -2dB to -18dB. Just insert the Drop Box between your amp's output and the speaker and you're ready to rock!

    $229.00
    ADD TO CART CHECKOUT NOW

    de Lisle Drop Box Linearly Variable 50W Attenuator

    $229.00
    ADD TO CART CHECKOUT NOW
    Successfully Added to your Shopping Cart
    Adding to Cart...
  • ￩
    ￫
    de Lisle Amp-Speaker Selector V2

    de Lisle Amp-Speaker Selector V2

    $289.00
    The de Lisle Amp-Speaker Selector V2 was designed as a studio tool to conveniently route the output of up to four amplifiers to various speaker cabinets. Just connect your amps' outputs to numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: the four switches on the front panel correspond to the four speaker connections. The 0-4 positions of each bank match that speaker cabinet to an amplifier (or 0 for not connected). Use multiple amps at the same time, swap speaker cabinets between amps, or connect multiple speakers to an amp in parallel. Signal and ground connections from the amps are always isolated from one another. And as a precaution, the unused amps see a load.
    Maximum quantity exceeded
    Minimum purchase amount of 0 is required
    de Lisle Amp-Speaker Selector V2

    de Lisle Amp-Speaker Selector V2

    The de Lisle Amp-Speaker Selector V2 was designed as a studio tool to conveniently route the output of up to four amplifiers to various speaker cabinets. Just connect your amps' outputs to numbered amplifier inputs on the rear panel. Then, hook up your speaker cabinets. Routing the signals is simple: the four switches on the front panel correspond to the four speaker connections. The 0-4 positions of each bank match that speaker cabinet to an amplifier (or 0 for not connected). Use multiple amps at the same time, swap speaker cabinets between amps, or connect multiple speakers to an amp in parallel. Signal and ground connections from the amps are always isolated from one another. And as a precaution, the unused amps see a load.
    $289.00
    ADD TO CART CHECKOUT NOW

    de Lisle Amp-Speaker Selector V2

    $289.00
    ADD TO CART CHECKOUT NOW
    Successfully Added to your Shopping Cart
    Adding to Cart...
  • de Lisle Amp-Speaker Selector V1

    de Lisle Amp-Speaker Selector V1

    $199.00
    The de Lisle Amp-Speaker Selector (Version 1) was designed as a studio tool to conveniently route the output from any of the connected amplifiers to an isolation cabinet. Alternatively, a single amplifier can be paired with one of up to three individual cabinets. Signal and ground connections from the amps are isolated, and as a precaution, the unused amps see a load. Similarly, when used as a cabinet selector, jacks with no cable inserted will be switched to an internal load. So, one can use a single cabinet or two cabinets without worrying about switching to an open cabinet jack.
    Maximum quantity exceeded
    Minimum purchase amount of 0 is required
    de Lisle Amp-Speaker Selector V1

    de Lisle Amp-Speaker Selector V1

    The de Lisle Amp-Speaker Selector (Version 1) was designed as a studio tool to conveniently route the output from any of the connected amplifiers to an isolation cabinet. Alternatively, a single amplifier can be paired with one of up to three individual cabinets. Signal and ground connections from the amps are isolated, and as a precaution, the unused amps see a load. Similarly, when used as a cabinet selector, jacks with no cable inserted will be switched to an internal load. So, one can use a single cabinet or two cabinets without worrying about switching to an open cabinet jack.
    $199.00
    ADD TO CART CHECKOUT NOW

    de Lisle Amp-Speaker Selector V1

    $199.00
    ADD TO CART CHECKOUT NOW
    Successfully Added to your Shopping Cart
    Adding to Cart...